Zusatzplatine zum D1 Mini Kompatibel mit Treiber für zwei Motoren. Fakten Beschriebung Name Pin I²C Takt SCL 5 (D1) I²C Daten SDA 4 (D2) Motor A Anschluss 1 1A Motor A Anschluss 2 2A Motor B Anschluss 1 1B Motor B Anschluss 2 2B Externe Spannungs VM(3 -10V) VM Externe Spannungs gnd GND GND I²C …
Continue reading "D1 Mini Shield – HR8833 Motor"
Motorplatine zur Ansteuerung von zwei Motoren (6,6v – 38V) über den I²C Bus Fakten Versorgungsspannung 6,6V – 38 V Maximaler dauer Strom 2A (kurzzeitig bis zu 3,6A) Steuerung Vorwärts/Rückwärt (geschwindigkeit) stop/bremsen Beschriebung Name Pin I²C Takt SCL 5 (D1) I²C Daten SDA 4 (D2) Motor A Anschluss 1 1A Motor A Anschluss 2 2A Motor …
Continue reading "D1 Mini Shield – AT8870 Motor"
Diese Sensorplatine besitzt einen SG30 Sensor welcher Organische Verbindungen und H2 in der luft detektiert und daraus den CO2 Wert errechnen kann (kein echter CO2 Sensor) Fakten I2C Interface TVOC Messung: 0-60000 ppb eCO2 Messung: 400-60000 ppm Sensor kann aus Platine gebrochen und über Buchse betrieben werden Φ2mm Befestigungslöcher Beschriebung Name D1 ESP32 S2 C3 …
Continue reading "D1 Mini Shield – SG30 Luftqualitätsmessung"
Zusatzplatine mit drei Steckverbinder zum Anschluss eines TFT Displays, des I2C Busses und eines IO Devices. Fakten TFT Buchse I²C Buchse IO Buchse TFT Buchse Anschluss Pin Bechreibung Name D1 ESP32 S2 C3 1 Hintergrundbeleuchtung TFT_LED NC 2 Masse GND GND 3 Reset TFT_RST RST 4 Register Select TFT_DC D8 15 5 A5 / 5 …
Continue reading "D1 Mini Shield – I2C Connector"
The WEMOS C3 is the latest in the D1 Mini format. A USB Micro connection, a reset button, and two built-in LEDs on the ESP are the only peripherals. In terms of its dimensions, it is rather small, with only a few pins brought out externally. However, the ESP32-C3 with its RISC-V CPU features Bluetooth 5.0. Interesting how...
Continue reading "(Wemos) C3 Mini"
An 8x8 LED Matrix in red. Facts 8x8 LED Matrix (One module) Data and clock lines are fixed and cannot be adjusted via solder bridges Description Name GPIO Clock CLK 14 Data DIN D7 Schematics Compatibility D1 Type Compatible Reason if not D1 mini Yes D1 mini Pro Yes Not tested D1 mini Lite Yes Not …
Continue reading "D1 Mini Shield – Matrix LED Shield"
This add-on board provides everything needed to control an OLED display. Facts OLED Display 64x48 Pixels Description Name D1 Mini D1 ESP32 I2C Data Pin SDA D2 GPIO 4 GPIO 32 I2C Clock Pin SCL D1 GPIO 5 GPIO 25 I2C Address 0x3C 0x3C D1 Mini Shield – OLED 64x48 – Pins…
Continue reading "D1 Mini Shield – Oled 64×48"
The WEMOS D1 EP32 is the replacement for the D1 Mini. It features an onboard ESP 32 Wroom module. A micro USB connector, a reset button and two built-in LEDs on the ESP are the only peripherals. In terms of its dimensions, it is rather small, however, this does not limit the number of…
Continue reading "(Wemos) D1 ESP32"
With the help of this add-on board, a few sounds can be coaxed from the D1 mini. Facts: A buzzer, nothing more, can be connected to the IOs D5-D8 via a solder bridge. No pre-selection was made in my case. Description: Name D1 D1 32 Input Buzzer, depending on the selected solder bridge BUZZER D5 / D6 / D7 / D8 GPIO 22/21/17/16 …
Continue reading "D1 Mini Shield – Buzzer (Pipser)"
The Pro version of the WEMOS D1 Mini has an external antenna connector and a soldered ceramic antenna. It also has more flash memory, specifically 16MB. Otherwise, it's the same as the Mini without Pro. Interesting about the WEMOS D1 Mini are the many expansion boards (see manufacturer). Facts USB Micro connector (CH340) Reset button 9 Digital Pins 1 Analogue Pin Operating voltage 3.3V Connection voltage…
Continue reading "Wemos D1 Mini Pro (V1.1.0)"